Lynx Studio Technology
home products news & events support how to buy company contact
Search
Support Center
Downloads
Contact Tech Support

Frequently Asked Questions
Aurora
LynxONE
LynxTWO/L22
Lynx AES16 / AES16e
Lynx LS-ADAT / LS-AES
LT-HD

Software Application Notes
Hardware Test Procedures
Connector Pin Outs
Other useful documents
Videos
Support Documents
Support Forum
User Manuals
Register Your Products
Buy Cables Now
Lynx LS-ADAT / LS-AES
• Getting Started/Installation
• Troubleshooting
• Operation
• Compatibility


  • How many LStream cards can I add to each LynxTWO/L22 or AES16 card?
  • Since the LS-ADAT provides 16 channels of I/O, and the Lynx Mixer has 16-channels, what happens to the other I/O when I’m using the LS-ADAT card?
  • How can I access LS-ADAT outputs with a LynxTWO or L22?
  • How can I access LS-AES outputs with a LynxTWO or L22?
  • How can I access LS-ADAT outputs with an AES16?
  • How can I access LS-ADAT inputs with a LynxTWO or L22?
  • How can I access LS-AES inputs with a LynxTWO or L22?
  • How can I access LS-ADAT inputs with an AES16?
  • How do I record 96Khz through the inputs of the LS-ADAT?
  • How do I install a second LS-AES card for the LynxTWO/L22?
  • Can I record or play 192kHz audio with the LS-AES?
  • How do I use ADAT sync as a clock source with the LS-ADAT card?
  • My LS-AES is supposed to be an 8-in/8-out card, but I only see 4 male and 4 female XLR connections. What gives?


How do I install a second LS-AES card for the LynxTWO/L22?
All OS
  1. Install the second LS-AES in a card slot adjacent to the first.
  2. Check to see if a shorting jumper is in place on the JP4 pins of the second LS-AES card. If so, please remove it to establish this card at Address 1.
  3. The included LStream ribbon cable connects a LynxTWO/L22 to either one or two LS-AES internal cards. Locate the cable end terminated in both a 14-pin and 2-pin receptacle. Connect the 14-pin receptacle to the connector labeled JP1 on the LynxTWO/L22. Take care to align the polarizing tab on the cable connector with the slot on the board connector. Failure to do may result in serious damage to the LynxTWO/L22 and LS-AES. Snap the 2-pin cable receptacle to connector labeled JP2/CLOCK IN on the LynxTWO/L22.
  4. Connect either of the two 16-pin cable connectors to connector JP1 on the LS-AES (labeled INT LSTREAM). Again, insure that the polarizing tab is aligned. In dual-card installations, both cable connectors are used.
  5. Replace the computer chassis cover, and power up the computer.
  6. Launch the Lynx Mixer. Click Settings> Advanced and select “LStream Dual Internal”
  7. One or both of the LStream cards must be set to “Slave” from the Clock Source selection in the LStream window for stable clock operation. Please see your Lynx documentation for information on appropriate clock settings for your Lynx card.
  8. Attach the Lynx digital I/O cable set to the second LS-AES card, and connect Out1 to a monitoring destination. As a default, the outputs from the second LS-AES card will utilize Lynx play devices 1–4. Test playback by opening an audio file in an audio application and directing the playback to Play1.

Home | Products | News & Events | Support | How To Buy | Company | Contact Us | Employment | Privacy

Lynx on Facebook   Support on Facebook 		© Copyright 2024, Lynx Studio Technology, Inc.