LT-HD firmware update failed

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Hi guys, working with an PTHD10 rig on Mountain Lion, with 2 Auroras 16 in a HDX card, and an Octo UAD Pci card. 
I did the firmware update to v28 of one Aurora, but I constantly failed the verify of the LT-HD update. Using a M Audio midisport 2x2, an 1 m usb cable and that worked for the Aurora. 
I've tried the Eeprom 2 to 1 switched and the rest of the AC with the sync source attemps...
I can't make it work. 
I was expierencing audio drops the last 3 weeks, so I face the firmware update as Paul indicated. Help please!!!

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Arielito Members Profile Send Private Message Find Members Posts Add to Buddy List Caracal Joined: December/22/2017 Location: Argentina Points: 4	Post Options Post Reply Quote Arielito Report Post Thanks(0) Quote Reply Topic: LT-HD firmware update failed Posted: December/23/2017 at 9:06am
	Hi guys, working with an PTHD10 rig on Mountain Lion, with 2 Auroras 16 in a HDX card, and an Octo UAD Pci card. I did the firmware update to v28 of one Aurora, but I constantly failed the verify of the LT-HD update. Using a M Audio midisport 2x2, an 1 m usb cable and that worked for the Aurora. I've tried the Eeprom 2 to 1 switched and the rest of the AC with the sync source attemps... I can't make it work. I was expierencing audio drops the last 3 weeks, so I face the firmware update as Paul indicated. Help please!!!

Mike N Members Profile Send Private Message Find Members Posts Add to Buddy List Admin Group Sales & Support Coordinator Joined: November/13/2008 Location: Costa Mesa, CA Points: 2488	Post Options Post Reply Quote Mike N Report Post Thanks(0) Quote Reply Posted: December/27/2017 at 4:32pm
	Is PT closed and the DigiLink disconnected? They should be. MIDI also needs to be connected in both directions, in case it's not... Edited by Mike N - December/27/2017 at 4:32pm
	Michael Nicoletti Lynx Studio Technology Sales & Support Coordinator 714-545-4700 Ext. 211

Arielito Members Profile Send Private Message Find Members Posts Add to Buddy List Caracal Joined: December/22/2017 Location: Argentina Points: 4	Post Options Post Reply Quote Arielito Report Post Thanks(0) Quote Reply Posted: December/27/2017 at 6:18pm
	Hi Mike, yes to both. I followed the steps exactly as it is on the Lynx web... Also switched the jumper from 2 to 1... And changed the midi interface. Always failed...

Mike N Members Profile Send Private Message Find Members Posts Add to Buddy List Admin Group Sales & Support Coordinator Joined: November/13/2008 Location: Costa Mesa, CA Points: 2488	Post Options Post Reply Quote Mike N Report Post Thanks(0) Quote Reply Posted: December/28/2017 at 9:24am
	Mac can be very picky with MIDI bulk dump updating. Interesting that the Aurora updated OK... You can try power cycling the Aurora before updating, or even a hard reset: 1. Power down the Aurora 2. Pull the AC power cable 3. Press and hold the Sample Rate button while plugging the unit back in. 4. Wait about 2 seconds, release the Sample Rate button 5. Power up the Aurora with the front panel switch.
	Michael Nicoletti Lynx Studio Technology Sales & Support Coordinator 714-545-4700 Ext. 211

Arielito Members Profile Send Private Message Find Members Posts Add to Buddy List Caracal Joined: December/22/2017 Location: Argentina Points: 4	Post Options Post Reply Quote Arielito Report Post Thanks(0) Quote Reply Posted: December/28/2017 at 10:40am
	I also did that, several times as I read old post in this forum. Interesting that switching even the interface (I´ve tried 3 differents) the update is resisting to be made...