E44 and CBL-ESYNC

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   If you don't have anything connected to Digital In 1, then there wouldn't be any clock showing for Digital In 1 and the input selectors would be RED instead of GREEN (indicating LOCK status).  Clearly, something is connected to Digital In 1.  Double check that you have the jumpers and switches on the card set properly.  The jumpers are right next to the HD15 connector and the switches are on the right hand side of the card when looking at the component side with the PCI Express connector down.

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
David A Hoatson Members Profile Send Private Message Find Members Posts Add to Buddy List Admin Group Forum Administrator Joined: October/01/2003 Location: Idaho Points: 4993	Topic: E44 and CBL-ESYNC Posted: October/20/2015 at 11:30am
	If you don't have anything connected to Digital In 1, then there wouldn't be any clock showing for Digital In 1 and the input selectors would be RED instead of GREEN (indicating LOCK status). Clearly, something is connected to Digital In 1. Double check that you have the jumpers and switches on the card set properly. The jumpers are right next to the HD15 connector and the switches are on the right hand side of the card when looking at the component side with the PCI Express connector down.
	Thank you, David A. Hoatson Lynx Studio Technology, Inc. Co-founder, Chief Software Engineer

linzo Members Profile Send Private Message Find Members Posts Add to Buddy List Caracal Joined: October/08/2015 Location: Russia Points: 17	Posted: October/20/2015 at 9:52am
	I have repeatedly checked with a multimeter pins 9 and 10 are NOT shorted together! Here is the main question I would gladly buy everything at once the cable together with the card, but at the time of purchase, the seller did not have esync ((

David A Hoatson Members Profile Send Private Message Find Members Posts Add to Buddy List Admin Group Forum Administrator Joined: October/01/2003 Location: Idaho Points: 4993	Posted: October/20/2015 at 9:21am
	Here is another way to look at the E44Sync connector pin out: www.lynxstudio.com/support_faq_result.asp?c=56 You can easily see that if pins 9 and 10 are shorted together, that will route the Digital Out 1 back into the Digital In 1. Obviously the easiest way to solve this problem is to use our factory E44Sync cable.
	Thank you, David A. Hoatson Lynx Studio Technology, Inc. Co-founder, Chief Software Engineer

linzo Members Profile Send Private Message Find Members Posts Add to Buddy List Caracal Joined: October/08/2015 Location: Russia Points: 17	Posted: October/20/2015 at 8:13am
	My problem on youtube http://youtu.be/pqwf2ln1Ohw

linzo Members Profile Send Private Message Find Members Posts Add to Buddy List Caracal Joined: October/08/2015 Location: Russia Points: 17	Posted: October/19/2015 at 9:23am
	Restore Defaults. All the same: When I plug esync cable, on the input1 i have a mirrored signal from output1 ((((( Edited by linzo - October/19/2015 at 9:24am

Mike N Members Profile Send Private Message Find Members Posts Add to Buddy List Admin Group Sales & Support Coordinator Joined: November/13/2008 Location: Costa Mesa, CA Points: 2488	Posted: October/19/2015 at 9:15am
	Hi, In Lynx Mixer, please try RESTORE DEFAULTS under the MIXER pulldown menu and let us know what happens.
	Michael Nicoletti Lynx Studio Technology Sales & Support Coordinator 714-545-4700 Ext. 211

linzo Members Profile Send Private Message Find Members Posts Add to Buddy List Caracal Joined: October/08/2015 Location: Russia Points: 17	Posted: October/18/2015 at 6:34am
	I've checked again with a multimeter: Pin 9(Digital Out1 Hot), Pin 10 (Digital In1 Cold), Pin 5 (Digital In 1 Hot), Pin 15 (Digital Out1 Cold) These pins are not connected together and are completely independent

linzo Members Profile Send Private Message Find Members Posts Add to Buddy List Caracal Joined: October/08/2015 Location: Russia Points: 17	Posted: October/17/2015 at 7:56am
	I'm try to disconnect w4s from Digital Out 1 and connect the emty (blank) esync cable without any plug on inputs and outputs - same problem: on the input1 i have a mirrored signal from output1 ((((( Edited by linzo - October/17/2015 at 9:26am

linzo Members Profile Send Private Message Find Members Posts Add to Buddy List Caracal Joined: October/08/2015 Location: Russia Points: 17	Posted: October/17/2015 at 5:25am
	If I put signal on Digital Out 2 all is ok http://www.imgzilla.ru/image.uploads/2015-10-17/original-80f0347e44b8bff08bfe233c65d30f09.jpg

linzo Members Profile Send Private Message Find Members Posts Add to Buddy List Caracal Joined: October/08/2015 Location: Russia Points: 17	Posted: October/17/2015 at 5:09am
	My Dac w4s is very happy with AES/EBU on Digital out 1 But when I plug 15 pin D-connecor I get the mirror signal on Digital In 1 like Digital out 1 I'm try to solder cable by myself. I follow the pinout table on the manual. http://stuartconnections.com/products/Computers/Peripherals/LCDs/Dell_1907FP/CD/graphics/15pin.gif But when I plug 15 pin D-connecor I get the mirror signal on Digital In 1 like Digital out 1 http://www.imgzilla.ru/image.uploads/2015-10-17/original-e5a5fdfcadb40b08057a4f0f72f73721.jpg I rang with a multimeter not once. All is exactly like in the manual. what's wrong ? Thank You Edited by linzo - October/17/2015 at 8:43am