Author |
Topic Search Topic Options
|
PaulTech
Admin Group
Joined: August/13/2004
Location: United States
Points: 5495
|
Topic: AES16 do not lock all inputs Posted: May/15/2014 at 4:11pm |
glad to hear it
|
|
|
SunPark
Caracal
Joined: March/20/2014
Location: Sweden
Points: 6
|
Posted: May/15/2014 at 11:26am |
SunPark wrote:
PaulTech wrote:
It is essential that the AES16 connected to the Aurora is in 4/4 mode, and the AES16 connected to the Apogee is in 8 ch mode. Can you verify that? |
Ok, I think I've tried that, but I'll have to check this for sure.
|
Yep!!! Now it's working, probably the only thing I didn't try...
Lots of thanks!
|
|
SunPark
Caracal
Joined: March/20/2014
Location: Sweden
Points: 6
|
Posted: May/13/2014 at 1:40am |
PaulTech wrote:
It is essential that the AES16 connected to the Aurora is in 4/4 mode, and the AES16 connected to the Apogee is in 8 ch mode. Can you verify that? |
Ok, I think I've tried that, but I'll have to check this for sure.
|
|
PaulTech
Admin Group
Joined: August/13/2004
Location: United States
Points: 5495
|
Posted: May/12/2014 at 5:04pm |
It is essential that the AES16 connected to the Aurora is in 4/4 mode, and the AES16 connected to the Apogee is in 8 ch mode. Can you verify that?
|
|
|
SunPark
Caracal
Joined: March/20/2014
Location: Sweden
Points: 6
|
Posted: May/09/2014 at 11:05am |
Mike N wrote:
Hi,
From the pic, it seems that only one 1605 cable is connected from the Aurora since only DIGITAL IN 1-4 are showing clock info...
Since you are using a DA16x, there is no AES signal going to AES16 #2's inputs and so there is no clock info shown.
|
1. there is two cables connected, tried switch them, tried switch AES16 cards, no difference.
2. why not? Aaaah didn't read it properly...
Could there be a problem with the AES16?
Latest firmware and drivers...
Thanks for replying...
Edited by SunPark - May/12/2014 at 8:28am
|
|
Mike N
Admin Group
Sales & Support Coordinator
Joined: November/13/2008
Location: Costa Mesa, CA
Points: 2488
|
Posted: May/09/2014 at 10:44am |
Hi,
From the pic, it seems that only one 1605 cable is connected from the Aurora since only DIGITAL IN 1-4 are showing clock info...
Since you are using a DA16x, there is no AES signal going to AES16 #2's inputs and so there is no clock info shown.
|
Michael Nicoletti Lynx Studio Technology Sales & Support Coordinator 714-545-4700 Ext. 211
|
|
SunPark
Caracal
Joined: March/20/2014
Location: Sweden
Points: 6
|
Posted: May/09/2014 at 10:27am |
Sorry, my fault, the screenshot shows this, during testing everything... It's been set that way, no difference...
But whatever i try the status of the cards shows the same thing...
Apogee is a DA16x, connected with a 1603 cable and the Aurora by two 1605.
|
|
Mike N
Admin Group
Sales & Support Coordinator
Joined: November/13/2008
Location: Costa Mesa, CA
Points: 2488
|
Posted: May/09/2014 at 9:29am |
Hi,
First thing is it appears you are also using a CBL-ICC cable. Set the AES16 #2 to "Header" as the clock source. There should only be one device set to INTERNAL.
Is the Apogee an AD16x or DA16x? They are not a single unit....
|
Michael Nicoletti Lynx Studio Technology Sales & Support Coordinator 714-545-4700 Ext. 211
|
|
SunPark
Caracal
Joined: March/20/2014
Location: Sweden
Points: 6
|
Posted: May/09/2014 at 4:51am |
Hi,
I'm helping a friend to set up his upgraded studio. Equipment are:
2xAES16 1xAurora16 1xApogee ADDA16x
These are connected with 1605 and 1603 cables. Clock syncs fine but the digital inputs does not lock in Lynx mixer adapter views...
I've switched AES cards, tried 4/4 and 8 I/O setup. And there is sound on some channels.
Regardless what I've tried it looks like this all the time...:
Any ideas?...
Thanks in advance,
//Pelle
|
|