| Author |
 Topic Search  Topic Options
|
Sonicsix 
Bobcat
Joined: December/11/2010
Points: 58
|
 Posted: June/18/2015 at 9:25am |
|
Thanks for all the Help Paul. I've deleted the Aggregrate, and haven't had a problem with sync dropping yet so far. I will keep working and see if this does it!
|
 |
PaulTech
Admin Group
Joined: August/13/2004
Location: United States
Points: 5495
|
Posted: June/18/2015 at 12:45pm |
|
Ah, good news!
|
|
|
|
Sonicsix
Bobcat
Joined: December/11/2010
Points: 58
|
Posted: June/20/2015 at 11:07am |
|
This is back using the 2192 as a master. At the moment it is without the aes hooked up on the 2192. As soon as I get caught up on sessions I'll try to hook up the AES connectors and see how thing work.
|
|
Sonicsix
Bobcat
Joined: December/11/2010
Points: 58
|
Posted: June/24/2015 at 5:21pm |
|
Ok, so I'm noticing that in the Lynx mixer that the external source (bnc?) sample rate isn't showing anything present, when I have the 2192 set as a master and feeding sync through bnc. Is this a problem? The Sample rate on the lynx mixer window for the digital 8 on aes16e 2 (2192 AES connection) is showing up as the correct sample rate now after deleting the PT aggregate.. In this arrangement, should the syncro lock be turned on?
|
|
Sonicsix
Bobcat
Joined: December/11/2010
Points: 58
|
Posted: June/25/2015 at 3:59pm |
|
Ok, as soon as I switched from 44.1 to 88.2 it went haywire again. I'm taking the 2192 out of the chain again and will try to see if I can get it to sync with the Aurora Lynx16 being the master. I also ordered an ICC cable to try to sync via AES16e like you mentioned. I will post a follow up after it arrives.
|
|
PaulTech
Admin Group
Joined: August/13/2004
Location: United States
Points: 5495
|
Posted: June/26/2015 at 4:07pm |
|
EXt not showing a rate is definitely a problem. Are you sure that the cable set that the 2192 wordclock is connected to is on Port A (digital in 1-4)?
|
|
|
|
PaulTech
Admin Group
Joined: August/13/2004
Location: United States
Points: 5495
|
Posted: June/26/2015 at 4:08pm |
|
You also might check if it can successfully slave to the 2192 digital input signal, rather than wordclock...
|
|
|
|
Sonicsix
Bobcat
Joined: December/11/2010
Points: 58
|
Posted: June/28/2015 at 4:48pm |
|
Yes I was using AES A as digital in sync, but the 2192 is connected and showing up on AES16e 2 Digital in 8.
|
|
Sonicsix
Bobcat
Joined: December/11/2010
Points: 58
|
Posted: July/06/2015 at 1:15pm |
The ICC cable showed up today and I have it installed and set up as: AES16e 1 master (internal sync), AES16e 2 slave (Header sync), both Aurora's set to AES A sync, and UA 2192 set to Word clock in (bnc from AES16e 1) Everything seems to be switching sample rates pretty smoothly so far. I had tried running 2192 to sync with AES in sync and It was showing up as incorrect sample rate in the Lynx Mixer Digital in window, seems good on BNC though. I'll test drive some more, but really happy that years of sync weirdness may have come to an end!!
|
|
PaulTech
Admin Group
Joined: August/13/2004
Location: United States
Points: 5495
|
Posted: July/07/2015 at 12:35pm |
|
If that setup doesn't work, I suspect some piece of hardware is malfunctioning.
Good luck
|
|
|
|
Sonicsix
Bobcat
Joined: December/11/2010
Points: 58
|
Posted: September/04/2015 at 5:02pm |
|
Ok so after things haves settled around here, I can report back. I am getting errors still after I change sample rate. It seems that when I check "allow sample rate change" in the mixer settings, It doesn't stay selected after a reboot. Could this possibly be a clue?
|
|
Sonicsix
Bobcat
Joined: December/11/2010
Points: 58
|
Posted: September/06/2015 at 1:24pm |
|
Ok, I have just seen that there are updates available. When I get some down time, I will install Core audio 58 and AES16e build 14. I will see if these will work and if I can get this to cooperate!
|
|
PaulTech
Admin Group
Joined: August/13/2004
Location: United States
Points: 5495
|
Posted: September/08/2015 at 5:18pm |
|
There was a change to driver build 58 that may be pertinent here, do give it a try. Make sure and update your firmware as well...
|
|
|
|
Sonicsix
Bobcat
Joined: December/11/2010
Points: 58
|
Posted: September/18/2015 at 1:48pm |
|
Updated Firmware and Core Audio to build 58 and The "allow time sync change" stays selected now. I'm assuming "Disable cpu power management" is supposed to be selected? I am still getting errors and digital ring modulated noise after changing sample rate......ugh. Is there any other ways to trouble shoot this?
|
|
PaulTech
Admin Group
Joined: August/13/2004
Location: United States
Points: 5495
|
Posted: September/18/2015 at 4:52pm |
Instead of using the aggregate, what if you just use one card. Same behavior? Does it help to increase the buffer size? You have the AES16e #1 on Internal, #2 on Header and the converters syncing to their digital inputs?
|
|
|
|
Sonicsix
Bobcat
Joined: December/11/2010
Points: 58
|
Posted: September/19/2015 at 4:39pm |
 PaulTech wrote:
Instead of using the aggregate, what if you just use one card. Same behavior? Does it help to increase the buffer size? You have the AES16e #1 on Internal, #2 on Header and the converters syncing to their digital inputs? |
I've tried switching to just 1 card/ Aurora and it still has ring modulation sound, sometimes on Aurora 1 and sometimes on #2. It seems to be worse now with the updated firmware and Audi driver. I have it sync'd with pcie #1 on internal, and pcie #2 on header within the Lynx mixer. I've tried the auroura's set to #1 internal, or aes sync source and Autora #2 set to aes sync.
|
|
Sonicsix
Bobcat
Joined: December/11/2010
Points: 58
|
Posted: September/24/2015 at 12:05pm |
|
I've even tried it in PT11,....still does it. It is worse now that I've updated firmware and Audio drivers. This is maddening. Nothing like tracking a band and playback is distorted and ring modulated while you are charging them. Does anyone know how to test generated clock sync to tell where this issue is coming from?! I'm about to start pricing alternative working equipment before I get blacklisted in the local recording community
|
|
PaulTech
Admin Group
Joined: August/13/2004
Location: United States
Points: 5495
|
Posted: September/24/2015 at 4:18pm |
There is something seriously off here. Might I suggest we expedite the solution by getting me remote access to your computer. I should be able to get to the bottom of this pretty quick that way. Call during our business hours or email a good time and I'll get you the log in information. support@lynxstudio.com Phone # in sig
|
|
|
|
Changing Buffer settings