LT-FW Clicks and Pops at 96K Solution

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

If you are using LT-FW and have Clcks and Pops at 48K and 96K, mine is working fine now.  This is what I did. 
Open the Aurora Remote Control and choose "Digital I/O and Settings"
Change "Sync Sourse" from Internal to Lslot LT-FW and wait for Auroa to Lock
After lock occurs, Switch "Sync Source" back to Internal

I've been using this method for six months now with absolutely no clicks, pops or distortion.  I use all sixteen analog and almost as many digital all simultaneously on a daily basis.  Rock-Solid!!

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
endorphin Members Profile Send Private Message Find Members Posts Add to Buddy List Caracal Joined: September/25/2012 Location: Virginia Points: 23	Topic: LT-FW Clicks and Pops at 96K Solution Posted: April/16/2014 at 7:20am
	If you are using LT-FW and have Clcks and Pops at 48K and 96K, mine is working fine now. This is what I did. Open the Aurora Remote Control and choose "Digital I/O and Settings" Change "Sync Sourse" from Internal to Lslot LT-FW and wait for Auroa to Lock After lock occurs, Switch "Sync Source" back to Internal I've been using this method for six months now with absolutely no clicks, pops or distortion. I use all sixteen analog and almost as many digital all simultaneously on a daily basis. Rock-Solid!!

PaulTech Members Profile Send Private Message Find Members Posts Add to Buddy List Admin Group Joined: August/13/2004 Location: United States Points: 5495	Posted: April/16/2014 at 5:40pm
	hmmm, very interesting... Does it matter if synchrolock does NOT lock?
	Paul Erlandson Lynx Studio Technology Support 714-545-4700 x 206 Lynx Support and Updates on Facebook!

endorphin Members Profile Send Private Message Find Members Posts Add to Buddy List Caracal Joined: September/25/2012 Location: Virginia Points: 23	Posted: April/16/2014 at 6:14pm
	Yes, synchroclock must lock first (and each time in and out). i own a CS400 PC by sweetwater. I run both 24 analog and 24 digital sumultaneously at 96K. I had a problem with this a while back and posted about it, but with this method of "initialization" it's been rock-solid each time with no problems.......Go figure! John (endorphin)

endorphin Members Profile Send Private Message Find Members Posts Add to Buddy List Caracal Joined: September/25/2012 Location: Virginia Points: 23	Posted: April/17/2014 at 6:10am
	I have a correction to my last post. I meant to write 16 analog and 16 digital simultaneously as I have only the Aurora 16. My other converter is 24 count, thus the confusion on my part. I've been using this setup for a Hybrid setup using the Lynx and the Dangerous Music gear and patching in the analog. The Aurora has been rock solid, I'm very happy about this.

PaulTech Members Profile Send Private Message Find Members Posts Add to Buddy List Admin Group Joined: August/13/2004 Location: United States Points: 5495	Posted: April/21/2014 at 3:27pm
	great, thanks for the feedback
	Paul Erlandson Lynx Studio Technology Support 714-545-4700 x 206 Lynx Support and Updates on Facebook!

endorphin Members Profile Send Private Message Find Members Posts Add to Buddy List Caracal Joined: September/25/2012 Location: Virginia Points: 23	Posted: April/22/2014 at 5:31am
	One final note. Sometimes it is necessary for me to do the following if the Aurora unit does not lock to the LT-FW signal. There are times the lock status for "LT-FW" will be red and read "Range". When this happens I have to do the following: 1. Exit the Aurora Remote Control Software 2. Exit all DAW applications using the converter and interface 3. Power down the Aurora 4. Remove the power plug from the rear of the Aurora Unit - Wait 10 seconds for good measure 5. Plug power cable back into Aurora Unit 6. Turn on Aurora from the front panel - Wait 30 seconds 7. Open Aurora Remote Control 8. Change clock source from "Internal" to "LT-FW" - LT-FW should lock within a minute 9. Once "LT-FW" is locked, switch from "LT-FW" back to "Internal" 10. Works for me, may work for you as well.